- Home
- ยป
- Our Products
- »
- Flow Sensors
Flow Sensors
REES52 QAV-R 220mm Quadcopter Combo Kit
Minimum Order Quantity: 1 Piece
Material | Plastic |
Usage/Application | Outdoor |
Model Name/Number | REES52 QAV-R 220mm Quadcopter Combo Kit |
Brand | REES52 |
Color | Black |
Features | Durable |
Pack Type | Box |
Country of Origin | Made in India |
- Full 3K Carbon Fiber airframe featuring 4mm removable arms
- Removable of arms
- Black Oxide steel screws
- Easy grip anodized spacers
- Multiple motor mounting holes to fit a variety of motors (M3 and M2 screw mounting patterns).
- Bumpers on the end of the arms to protect the motor during a crash, just like the QAV250.
- Easy Lipo Access
- Support for 32mm board cams as well as 26mm cams.
- Support to carry HD camera (such as the GoPro 4, Mobius, or GoPro Session) with optional camera vibration mount (not included)
Package Includes:
- 1 x QAV-R 220mm Quadcopter Combo Kit
Kit includes:
- 1 x QAV-R 220mm Quadcopter Carbon fiber frame
- 4 x RS 2205 2300KV Brushless Motors (2 x cw and 2 x ccw)
- 4 x LittleBee BL Heli-S 30A-s ESCs
- 4 x 3-LED RGB Strip Board
- 2 x 5030 Propellor Pair
- 2 x 5045 Triblade Propeller Pair
- 1 x SP Racing F3 Arco Flight controller
- 1 x Mateksys PDB-X60 w/BEC 5V & 12V
- 1 x Fitting Accessories set
Additional Information:
- Delivery Time: 3 days
Nano V3.0 Development Board
Minimum Order Quantity: 1 Piece
Operating Voltage (VDC) | 2.7v |
Model Name/No. | Nano 33 IoT |
Series | Nano Family |
Brand | REES52 |
Processor Brand | Atmel |
Digital I/O Pins | 14 (of which 6 provide PWM output) |
Maximum supply voltage (not recommended) | 20 V |
Supply Voltage (recommended) | 12 V |
Country of Origin | Made in India |
Additional Information:
- Delivery Time: 3 days
YF-DN50 2 inch Water Flow Sensor
Minimum Order Quantity: 10 Piece
Product Brochure
Material | Plastic |
Sensor | Hall effect |
Working voltage range | DC 5-18 V |
Allow compression | Water pressure 1.75 Mpa below |
Maximum current | 15 mA (5 volt DC) |
Features | Eco Friendly |
Model No | YF-DN50 |
Flow range | 10-200 Liter per min |
Installation direction: Vertical (inclination should not exceed 5 degrees.
Specification:
- Waterproof,Heat resistance,pressure resistance,cold resistance.
- Easy to install.
- Flow range:10-200L/min
- Sensor:Hall effect
- Maximum current:15 mA(DC 5V)
- Working voltage range:DC 3.5-12 V
- Load capacity:¡Ü10 mA(DC 5V)
- Operating Temp:up to 80C,Operating humidity:35%-90%RH
- Allow compression:Water pressure 1.75 Mpa below
- Insulation resistance:>100M OHM
- Storage Temperature:-25-80C
- Storage humidity:25%-95%RH
- Output Waveform:Square Wave,output pulse signal.
- Cable length:480mm
- Max Size:92mm*68mm
Additional Information:
- Production Capacity: 1000
- Delivery Time: 4-5 Working Days
- Packaging Details: 1 x Water Flow Sensor - YF-DN50
Water Flow Sensor
Minimum Order Quantity: 100 Piece
Type | Water Flow Sensor |
Brand | Sea |
Part Number | YF-G1 |
Application | Industrial |
Flow Rate | 2.0 M Pa |
Material | Plastic |
Oprating Voltage | 24 VDC |
Color | Black |
- Sea Pass/QC
- water Flow sensor
- working range- 2-100 l/min
- water pressure,< 2.0 M Pa
- Oprating Voltage; 3.5-24 VDC
39.1mm Force Sensor
Minimum Order Quantity: 10 Piece
Force Range | 0 - 7.5 kN |
Actuation Force: | 0.1 Newtons |
Device Rise Time: | <3 microseconds |
Force Sensitivity Range: | Force Sensitivity Range: 0.1 - 10.02 Newtons |
Non-Actuated Resistance: | 10M W |
Shape | Square |
Features | Durable |
Country of Origin | Made in India |
This is a Force sensitive resistor with a square, 1.75x1.5",sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lowerthe resistance. When no pressure is being applied to the FSR its resistance will be larger than 1M. This FSR can sense applied force anywhere in the range of 100g-10kg.
Two pins extend from the bottom of the sensor with 0.1" pitch making it bread board friendly. There is a peel-and-stick rubber backing on the other side of the sensing area to mount the FSR.
Just Connect a resistor to form a voltage divider and measure the voltage at the junction to find the force applied. These sensors are simple to set up and great for sensing pressure, but they aren't incredibly accurate. Use them to sense if it's being squeezed, but you may not want to use it as a scale.
Features:
- Actuation Force: 0.1 Newtons
- Force Sensitivity Range: 0.1 - 10.02 Newtons
- Non-Actuated Resistance: 10M W
- Device Rise Time: <3 microseconds
- Temp Operating Range: 30 - +70 ºC
- 16MHz Clock Speed
- 32 KB Flash Memory
- Overall length: 1.75"
- Overall width: 0.28"
- Sensing area: 0.3"
Additional Information:
- Item Code: force
- Production Capacity: 1000
- Delivery Time: 4 to 5 Working Days
- Packaging Details: 1 x Force Sensor
MS 4525DO Air Speed Sensor And Pitot Tube Set for Pixhawk
Minimum Order Quantity: 1 Piece
Application | Automobile |
Output signal | Analog |
Supply Current | 6 mA |
Operating frequency | 0 to 12 KHz |
Operating Temperature | -40 to 125 Deg C |
IP rating | IP44 |
Resolution | 0.84Pa |
Data | 14 bits from a 24 bit |
Model | MS 4525DO |
Measurement Range | 1psi, 100m/s (223mph/360kmh) |
Country of Origin | Made in India |
Want to have a very accurate reading of your PIXHAWK airspeed?, then look no further than the Pixhawk Digital Airspeed Sensor which is supplied with its own pitot tube. This MS 4525DO Air Speed Sensor And Pitot tube Set for Pixhawk must be used in conjunction with the Pixhawk PX4 autopilot system.
This unit has a very high resolution, low offset digital pressure sensor which enables it to register extremely accurate airspeed readings. This sensor does not suffer from noise caused by long cables or from offsets caused by ratio-metric outputs which older analog airspeed systems suffer from.
The Measurement Specialities 4525DO sensor is capable of measuring speeds of up to 100m/s (223mph/360kmh) using a 0.84 Pa with data delivered at 14 bits from a 24 bit delta-sigma ADC. This airspeed sensor also has a built-in temperature sensor to allow the calculation of true airspeed from the indicated airspeed using the MS5611 static pressure sensor on the Pixhawk PX4.
Featuring a Measurement Specialties 4525DO sensor, with a 1 psi measurement range (roughly up to 100 m/s or 360 km/h or 223 mp/h), the Pixhawk Airspeed Sensor Kit enables a resolution of 0.84 Pa, with data delivered at 14 bits from a 24 bit delta-sigma ADC.
It also measures temperature to allow calculation of true airspeed from indicated airspeed using the MS5611 static pressure sensor on Pixhawk. Not influenced by the heat of nearby processing components, it is much closer to the air temperature than with previous analog sensor setups. Supported on all Pixhawk and PX4 autopilot generation boards, this kit comes with M3 / 6-32 mounting holes.
If you are flying multi-copters then you do not require this unit as it is only usable if you are using the fixed-wing code in the Pixhawk.
Features:
- Digital airspeed sensor
- Rubber tubing
- Pitot tube
- Four-wire I2C cable
Package Included:
- 1 x MS 4525DO Air Speed Sensor Module
- 1 x Pitot Tube
- 1 x Silicone tube.
- 1 x 4 pin cable
Additional Information:
- Item Code: RS3531
- Production Capacity: 100
- Delivery Time: 5 Days
- Packaging Details: 1 x MS 4525DO Air Speed Sensor Module, 1 x Pitot Tube, 1 x Silicone tube, 1 x 4-pin cable
BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module
Minimum Order Quantity: 100 Piece
Type | Barometric |
Brand | REES52 |
Part Number | RS1033 |
Pressure Range | 300 hPa ~ 1100 hPa |
Accuracy | 700 to 900hPa and 25 to 40 deg. C: +-0.12hPa and +-1.0m |
Supply Voltage | 1.71V to 3.6V |
Interface | I2C/SPI |
Operating Temperature | -40 to +85 deg. Celsius |
BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module is a cheapest and tiny Atmospheric Sensor Breakout to measure barometric pressure, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BMP280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
This module uses an environmental sensor manufactured by Bosch with temperature, a barometric pressure sensor that is the next generation upgrade to the popular BMP085/BMP180/BMP183 Sensor. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI; This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude and the pressure measurements are so good; you can also use it as an altimeter with ±1 meter accuracy.
The BMP280 is the next-generation of sensors and is the upgrade to the BMP085/BMP180/BMP183 – with a low altitude noise of 0.25m and the same fast conversion time. It has the same specifications but can use either I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.
Features:
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V.
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C).
- Peak current: 1.12mA.
- Operating Pressure: 300 hPa to 1100 hPa.
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.
Additional Information:
- Production Capacity: 1000
- Delivery Time: 4-5 Working Days
- Packaging Details: 1 x BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module 1 x Header set (Without Soldered)
Waveshare PicoGo Mobile Robot
Minimum Order Quantity: 1 Unit
Payload Capacity | 10 Kg |
Usage/Application | Commercial |
Brand | Waveshare |
Display | Digital |
Features | Durable |
Pack Type | Box |
Color | Black |
Country of Origin | Made in India |
- Product Features Smart robot is always the favorite project of electronic enthusiasts, and there've been several robots based on Raspberry Pi Zero W, 3B+, 4B in Waveshare's product line. Now, here comes the Pico version: PicoGo!
- The PicoGo is a smart mobile robot based on Raspberry Pi Pico, it includes ultrasonic module, LCD module, Bluetooth module, line following module, and obstacle avoidance module, all these functions are highly integrated for easily achieving IR obstacle avoidance, auto line following, Bluetooth/IR remote control, and more. With various advanced features, it will help you fast get started with smart robot design and development.
Additional Information:
- Delivery Time: 3 days
Waveshare NB-IoT / Cat-M(EMTC) / GNSS HAT
Minimum Order Quantity: 1 Hour
Features | Eco Friendly |
Pack Type | Box |
Logic level | 5V / 3.3V (configured via jumper) |
Overall current (idle mode) | 39mA |
Power supply voltage | 5V |
Dimension | 30.2mm x 65mm |
Shape | Rectangle |
Color | Blue |
This is a telecommunication HAT which features multi communication functionalities: NB-IoT (NarrowBand-Internet of Things), Cat-M (aka eMTC, enhanced Machine Type Communication), and GNSS (Global Navigation Satellite System).
With the developing of telecommunication technology LTE, 2G/3G networks are fading away, the future world would be dominated by IoT technologies consisting of low bandwidth NB-IoT/Cat-M and high bandwidth 4G/5G standards.
This HAT supports global bands of NB-IoT and Cat-M, as well as positioning function. Due to its advantages like small size, low delay, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, e-health, and so on.
Additional Information:
- Delivery Time: 3 days